#!/bin/sh

LOG_NAME=/opt/wz_mini/log/wz_user
if [[ -e $LOG_NAME.log || -L $LOG_NAME.log ]] ; then
    i=0
    while [[ -e $LOG_NAME.log.$i || -L $LOG_NAME.log.$i ]] ; do
        let i++
    done
        mv $LOG_NAME.log $LOG_NAME.log.$i
    LOG_NAME=$LOG_NAME
fi
touch -- "$LOG_NAME".log
exec 1> $LOG_NAME.log 2>&1

set -x

echo "welcome to wz_user.sh"
echo "PID $$"


if [[ -e /tmp/dbgflag ]];then
        echo "debug mode, disabled"
        exit 0
fi

export WZMINI_CFG=/opt/wz_mini/wz_mini.conf

[ -f $WZMINI_CFG ] && source $WZMINI_CFG

hostname_set() {
	echo "set hostname"
	hostname $CUSTOM_HOSTNAME
}

first_run_check() {
	if [ -e /opt/wz_mini/tmp/.wz_user_firstrun ]; then
	echo "wz_user.sh already run once, exit."
	exit 0
	fi
}

store_mac() {
	echo "store original mac"
	cat /sys/class/net/wlan0/address | tr '[:lower:]' '[:upper:]' > /opt/wz_mini/tmp/wlan0_mac
}

wait_wlan() {
##Check if the driver has been loaded for the onboard wlan0, store the MAC.
    while true
    do
        if ifconfig wlan0 | grep "HWaddr"; then
		echo "wlan0 hwaddr is up"
	        store_mac
		break
        else
	        echo "wlan0 hwaddr not ready yet..."
        	sleep 5
	fi
    done
}

wpa_check() {
##Check if wpa_supplicant has been created by iCamera
	if [ -e /tmp/wpa_supplicant.conf ]; then
		wait_wlan
		echo "wpa_supplicant.conf ready"
	else
		echo "wpa_supplicant.conf not ready, wait some time for creation."
		COUNT=0
		ATTEMPTS=15
		until [[ -e /tmp/wpa_supplicant.conf ]] || [[ $COUNT -eq $ATTEMPTS ]]; do
		echo -e "$(( COUNT++ ))... \c"
		sleep 5
		wpa_check
		done
		if [[ $COUNT -eq $ATTEMPTS ]]; then
			echo "time exceeded waiting for iCamera, continue potentially broken condition without network."
		fi
	fi
}

wlanold_check() {
#Have we renamed interfaces yet?
	if [ -d /sys/class/net/wlanold ]; then
		echo "wlanold exist"
		eth_wlan_up
	else
		echo "wlanold doesn't exist"
                if [[ "$BONDING_ENABLED" == "true" ]] && ([[ "$ENABLE_USB_ETH" == "true" ]] || [[ "$ENABLE_USB_DIRECT" == "true" ]]); then
			rename_interface_and_setup_bonding bond0 "$BONDING_PRIMARY_INTERFACE" "$BONDING_SECONDARY_INTERFACE"
		else
			rename_interface $1
		fi
	fi
}

netloop() {
##While loop for check
        while true
        do
	wlanold_check $1
        echo "wlan0 not ready yet..."
        sleep 5
        done
}

rename_interface() {
##Fool iCamera by renaming the hardline interface to wlan0
	echo "renaming interfaces"
	ifconfig $1 down
	ifconfig wlan0 down
        /opt/wz_mini/bin/busybox ip link set wlan0 name wlanold
        /opt/wz_mini/bin/busybox ip addr flush dev wlanold
        /opt/wz_mini/bin/busybox ip link set $1 name wlan0
	eth_wlan_up
}

rename_interface_and_setup_bonding() {
##Fool iCamera by renaming the hardline interface to wlan0
## $1 Bonding Interface, $2 Primary Interface, $3 Secondary Interface
	bonding_interface=$1
	primary_interface=$2
	secondary_interface=$3

	echo "renaming interfaces"

	# Bring all interfaces down
	ifconfig $bonding_interface down
	ifconfig $primary_interface down
	ifconfig $secondary_interface down

	# Have to bring bonding interface up to be able to bond our slaves.
	/opt/wz_mini/bin/busybox ip link set $bonding_interface up

	# Rename the real wlan0 interface if needed/used
	if [[ "$primary_interface" == "wlan0" ]]; then
		/opt/wz_mini/bin/busybox ip link set $primary_interface name wlanold
		/opt/wz_mini/bin/busybox ip addr flush dev wlanold
		primary_interface="wlanold"
		# Because we just changed the name of the primary interface, we need to
		# tell the bonding driver about the name change as well.
		echo "$primary_interface" > /sys/devices/virtual/net/$bonding_interface/bonding/primary
	fi
	if [[ "$secondary_interface" == "wlan0" ]]; then
		/opt/wz_mini/bin/busybox ip link set $secondary_interface name wlanold
		/opt/wz_mini/bin/busybox ip addr flush dev wlanold
		secondary_interface="wlanold"
	fi

	# Enslave the Ethernet and Original Wifi interfaces
	# under the bonding interface.
	/opt/wz_mini/tmp/.bin/ifenslave $bonding_interface $primary_interface $secondary_interface

	# Have to bring bonding interface down to be rename the interface
	/opt/wz_mini/bin/busybox ip link set $bonding_interface down

	# Name the bonding interface to be the "new" wlan0 interface
	/opt/wz_mini/bin/busybox ip link set $bonding_interface name wlan0

	# Bring the newly renamed wlan0 (actually the bond interface) back up
	eth_wlan_up
}

bonding_setup() {
echo "bonding kernel module setup"
if [[ "$BONDING_ENABLED" == "true" ]]; then
	if [[ "$BONDING_LINK_MONITORING_FREQ_MS" == "" ]]; then
        	BONDING_LINK_MONITORING_FREQ_MS="100"
	fi
	if [[ "$BONDING_DOWN_DELAY_MS" == "" ]]; then
            BONDING_DOWN_DELAY_MS="5000"
        fi
        if [[ "$BONDING_UP_DELAY_MS" == "" ]]; then
            BONDING_UP_DELAY_MS="5000"
        fi
        if [[ "$BONDING_PRIMARY_INTERFACE" == "" ]]; then
            BONDING_PRIMARY_INTERFACE="$1"
        fi
        if [[ "$BONDING_SECONDARY_INTERFACE" == "" ]]; then
            BONDING_SECONDARY_INTERFACE="$2"
        fi
        if [[ "$BONDING_FAIL_OVER_MAC" == "" ]]; then
            BONDING_FAIL_OVER_MAC="0"
        fi

	# Insert the bonding driver into the kernel
	insmod $KMOD_PATH/kernel/drivers/net/bonding/bonding.ko mode=active-backup miimon="$BONDING_LINK_MONITORING_FREQ_MS" downdelay="$BONDING_DOWN_DELAY_MS" updelay="$BONDING_UP_DELAY_MS" primary="$BONDING_PRIMARY_INTERFACE" fail_over_mac="$BONDING_FAIL_OVER_MAC"
fi
}

eth_wlan_up() {
##Run DHCP client, and bind mount our fake wpa_cli.sh to fool iCamera
        ifconfig wlan0 up
	pkill udhcpc
        udhcpc -i wlan0 -x hostname:$CUSTOM_HOSTNAME -p /var/run/udhcpc.pid -b

    # If running with Interface Bonding enabled, kill any existing
    # wpa_supplicant that might be running and spawn our own instead
    if [[ "$BONDING_ENABLED" == "true" ]] && ([[ "$ENABLE_USB_ETH" == "true" ]] || [[ "$ENABLE_USB_DIRECT" == "true" ]]); then
        /opt/wz_mini/bin/busybox killall wpa_supplicant
        wpa_supplicant -D nl80211 -i wlanold -c /tmp/wpa_supplicant.conf -B -s
    fi

	if [ -f /opt/wz_mini/tmp/.T20 ]; then
        mount -o bind /opt/wz_mini/bin/wpa_cli.sh /system/bin/wpa_cli
	else
        mount -o bind /opt/wz_mini/bin/wpa_cli.sh /bin/wpa_cli
	fi

	break
}

swap_enable() {
        if [ -e /opt/wz_mini/swap ]; then
                echo "Swap file exists"
                if cat /proc/swaps | grep "mini" ; then
                        echo "Swap is already enabled"
                else
                        echo "Enable swap"
                        swapon /opt/wz_mini/swap
                fi
        else
                echo "Swap file missing!"
        fi
}

dmesg_log() {

DMESG_LOG=/opt/wz_mini/log/dmesg
if [[ -e $DMESG_LOG.log || -L $DMESG_LOG.log ]] ; then
    i=0
    while [[ -e $DMESG_LOG.log.$i || -L $DMESG_LOG.log.$i ]] ; do
        let i++
    done
        mv $DMESG_LOG.log $DMESG_LOG.log.$i
    DMESG_LOG=$DMESG_LOG
fi
touch -- "$DMESG_LOG".log
dmesg > $DMESG_LOG.log 2>&1

}

trim_logs() {

echo "Deleting logs older than 5 boots..."

find /opt/wz_mini/log -name '*log*' | while read file; do
  [ "${file#/opt/wz_mini/log/*log.}" -gt 5 ] && rm -v "$file"
done

}

first_run_check
wpa_check

#Set module dir depending on platform
if [ -f /opt/wz_mini/tmp/.T20 ]; then
	KMOD_PATH="/opt/wz_mini/lib/modules/3.10.14"
else
	KMOD_PATH="/opt/wz_mini/lib/modules/3.10.14__isvp_swan_1.0__"
fi

swap_enable

if [[ "$ENABLE_IPV6" == "true" ]]; then
	echo "ipv6 enabled"
else
	echo "ipv6 disabled"
	sysctl -w net.ipv6.conf.all.disable_ipv6=1
fi

if [[ "$ENABLE_NFSv4" == "true" ]]; then
        insmod $KMOD_PATH/kernel/lib/oid_registry.ko
        insmod $KMOD_PATH/kernel/net/dns_resolver/dns_resolver.ko
        insmod $KMOD_PATH/kernel/fs/nfs/nfsv4.ko
        insmod $KMOD_PATH/kernel/net/sunrpc/auth_gss/auth_rpcgss.ko
        echo nfsv4 enabled
else
        echo nfsv4 disabled
fi

if [[ "$ENABLE_IPTABLES" == "true"  ]]; then

	insmod $KMOD_PATH/kernel/net/netfilter/x_tables.ko
	insmod $KMOD_PATH/kernel/net/ipv4/netfilter/ip_tables.ko
	insmod $KMOD_PATH/kernel/net/ipv4/netfilter/ipt_REJECT.ko
	insmod $KMOD_PATH/kernel/net/ipv4/netfilter/iptable_filter.ko
	insmod $KMOD_PATH/kernel/net/ipv4/netfilter/iptable_mangle.ko
	echo "iptables ipv4 enabled"

	if [[ "$ENABLE_IPV6" == "true" ]]; then
		insmod $KMOD_PATH/kernel/net/ipv6/netfilter/ip6_tables.ko
		insmod $KMOD_PATH/kernel/net/ipv6/netfilter/ip6t_REJECT.ko
		insmod $KMOD_PATH/kernel/net/ipv6/netfilter/ip6table_filter.ko
		insmod $KMOD_PATH/kernel/net/ipv6/netfilter/ip6table_mangle.ko
		echo "iptables ipv6 enabled"
	fi
else
	echo "iptables disabled"
fi

if [[ "$ENABLE_USB_ETH" == "true" ]]; then

	insmod $KMOD_PATH/kernel/drivers/net/usb/usbnet.ko

	# Auto-Detect an Ethernet Driver and load it
	if [[ "$ENABLE_USB_ETH_MODULE_AUTODETECT" == "true" ]]; then
		for DEVICE in `lsusb | awk '{print $6}'| tr '[:upper:]' '[:lower:]'`; do
			case $DEVICE in
			'077b:2226' | '0846:1040' | '2001:1a00' | '0b95:1720' | '07b8:420a' |\
			'08dd:90ff' | '0557:2009' | '0411:003d' | '0411:006e' | '6189:182d' |\
			'0df6:0056' | '07aa:0017' | '1189:0893' | '1631:6200' | '04f1:3008' |\
			'17ef:7203' | '0b95:772b' | '0b95:7720' | '0b95:1780' | '0789:0160' |\
			'13b1:0018' | '1557:7720' | '07d1:3c05' | '2001:3c05' | '2001:1a02' |\
			'1737:0039' | '04bb:0930' | '050d:5055' | '05ac:1402' | '0b95:772a' |\
			'14ea:ab11' | '0db0:a877' | '0b95:7e2b' | '0b95:172a' | '066b:20f9')
				echo "Loading ASIX Ethernet driver..."
				modprobe asix
				;;
			'0b95:1790' | '0b95:178a' | '0df6:0072')
				echo "Loading AX88179 Gigabit Ethernet driver..."
				modprobe ax88179_178a
				;;
			'1004:61aa' | '046d:c11f' | '1410:b001' | '1410:9010' | '413c:8195' |\
			'413c:8196' | '413c:819b' | '16d5:650a' | '12d1:14ac')
				echo "Loading USB CDC Ethernet driver..."
				modprobe cdc_ether
				;;
			'0bda:8152')
				echo "Loading Realtek RTL8152 driver..."
				modprobe r8152
				;;
			esac
		done
	fi

	# Manually load any other Ethernet Drivers if asked for
	if [[ "$ENABLE_USB_ETH_MODULE_MANUAL" != "" ]]; then
		for i in $(echo "$ENABLE_USB_ETH_MODULE_MANUAL" | tr "," "\n")
		do
			insmod $KMOD_PATH/kernel/drivers/net/usb/$i.ko
		done
	fi

	bonding_setup eth0 wlan0

	swap_enable

	netloop eth0

	else
	echo "USB Ethernet disabled"
fi

if [[ "$ENABLE_USB_DIRECT" == "true" ]]; then

        HOST_MACADDR=$(echo "$CUSTOM_HOSTNAME"|md5sum|sed 's/^\(..\)\(..\)\(..\)\(..\)\(..\).*$/02:\1:\2:\3:\4:\5/')

        if [ -f /opt/wz_mini/tmp/.T20 ]; then
		echo connect > /sys/devices/platform/jz-dwc2/dwc2/udc/dwc2/soft_connect
		sleep 1
		devmem 0x10000040 32 0x0b800096
		sleep 1
		devmem 0x13500000 32 0x001100cc
	else
		#Set dwc2 ID_PIN driver memory
		devmem 0x13500000 32 0x001100cc
		devmem 0x10000040 32 0x0b000096
		#wipe the bits to set the ID_PIN, only for the V3.
		devmem 0x10000040 32 0x0b000FFF
	fi

	insmod $KMOD_PATH/kernel/drivers/usb/gadget/libcomposite.ko

        if [ -f /opt/wz_mini/tmp/.T31 ]; then
	insmod /opt/wz_mini/lib/modules/3.10.14__isvp_swan_1.0__/kernel/drivers/usb/gadget/u_ether.ko
	insmod /opt/wz_mini/lib/modules/3.10.14__isvp_swan_1.0__/kernel/drivers/usb/gadget/usb_f_ncm.ko
	fi

	insmod $KMOD_PATH/kernel/drivers/usb/gadget/g_ncm.ko iManufacturer=wz_mini_ncm host_addr="$HOST_MACADDR" dev_addr="$USB_DIRECT_MAC_ADDR"

	sleep 1

	bonding_setup usb0 wlan0

	swap_enable

	#loop begin
	while true
	do
	netloop usb0
	echo "wlan0 not ready yet..."
        sleep 1
	done
	else
	echo "USB Direct disabled"
fi

if [[ "$ENABLE_USB_RNDIS" == "true" ]]; then
        if [[ "$ENABLE_USB_ETH" == "true" ]] || [[ "$ENABLE_USB_DIRECT" == "true" ]]; then
                echo "RNDIS is not compatible with ENABLE_USB_ETH or ENABLE_USB_DIRECT.  Please enable only ENABLE_USB_RNDIS"
        else

                insmod $KMOD_PATH/kernel/drivers/net/usb/usbnet.ko
                insmod $KMOD_PATH/kernel/drivers/net/usb/cdc_ether.ko
                insmod $KMOD_PATH/kernel/drivers/net/usb/rndis_host.ko

                sleep 1

                swap_enable

                #loop begin
                while true
                do
                wpa_check usb0
                echo "wlan0 not ready yet..."
                sleep 1
                done
        fi
else
        echo "usb rndis disabled"
fi

if [[ "$ENABLE_WIREGUARD" == "true" ]]; then
	insmod $KMOD_PATH/kernel/net/ipv4/tunnel4.ko
	insmod $KMOD_PATH/kernel/net/ipv4/ip_tunnel.ko
	insmod $KMOD_PATH/kernel/net/wireguard/wireguard.ko

	if [[ "$WIREGUARD_IPV4" != "" ]]; then

		if [ -d /opt/wz_mini/etc/wireguard ]; then
			echo "wireguard dir exists"
		else
			mkdir -p /opt/wz_mini/etc/wireguard
		fi

	if [ ! -f /opt/wz_mini/etc/wireguard/privatekey ]; then
		(umask 277 && /opt/wz_mini/bin/wg  genkey | /opt/wz_mini/bin/busybox tee /opt/wz_mini/etc/wireguard/privatekey | /opt/wz_mini/bin/wg  pubkey > /opt/wz_mini/etc/wireguard/publickey)
	fi

	/opt/wz_mini/bin/busybox ip link add dev wg0 type wireguard
	/opt/wz_mini/bin/busybox ip address add dev wg0 "$WIREGUARD_IPV4"
	/opt/wz_mini/bin/wg set wg0 private-key /opt/wz_mini/etc/wireguard/privatekey
	/opt/wz_mini/bin/busybox ip link set wg0 up
	fi

	if [[ "$WIREGUARD_PEER_PUBLIC_KEY" != "" ]] && [[ "$WIREGUARD_PEER_ALLOWED_IPS" != "" ]] && [[ "$WIREGUARD_PEER_ENDPOINT" != "" ]] && [[ "$WIREGUARD_PEER_KEEP_ALIVE" != "" ]]; then
		/opt/wz_mini/bin/wg set wg0 peer "$WIREGUARD_PEER_PUBLIC_KEY" allowed-ips "$WIREGUARD_PEER_ALLOWED_IPS" endpoint "$WIREGUARD_PEER_ENDPOINT" persistent-keepalive "$WIREGUARD_PEER_KEEP_ALIVE"
		/opt/wz_mini/bin/busybox ip route add "$WIREGUARD_PEER_ALLOWED_IPS" dev wg0
	fi
else
	echo "wireguard disabled"
fi

if [[ "$ENABLE_CIFS" == "true" ]]; then
	insmod $KMOD_PATH/kernel/fs/cifs/cifs.ko
else
	echo "cifs disabled"
fi

if [[ "$ENABLE_USB_STORAGE" == "true" ]]; then
	insmod $KMOD_PATH/kernel/drivers/scsi/scsi_mod.ko
	insmod $KMOD_PATH/kernel/drivers/scsi/sd_mod.ko
	insmod $KMOD_PATH/kernel/drivers/usb/storage/usb-storage.ko
else
	echo "usb_storage disabled"
fi

if [[ "$ENABLE_EXT4" == "true" ]]; then
        if [ -f /opt/wz_mini/tmp/.T20 ]; then
	insmod $KMOD_PATH/kernel/lib/crc16.ko
	fi

	insmod $KMOD_PATH/kernel/fs/jbd2/jbd2.ko
	insmod $KMOD_PATH/kernel/fs/mbcache.ko
	insmod $KMOD_PATH/kernel/fs/ext4/ext4.ko
else
	echo "ext4 disabled"
fi

if [[ "$DISABLE_FW_UPGRADE" == "true" ]]; then
	mkdir /tmp/Upgrade
	mount -t tmpfs -o size=1,nr_inodes=1 none /tmp/Upgrade
	#Setting this host causes iCamera to segfault, lets ignore it for now
	#echo -e "127.0.0.1 localhost \n127.0.0.1 wyze-upgrade-service.wyzecam.com" > /opt/wz_mini/tmp/.storage/hosts
	#mount --bind /opt/wz_mini/tmp/.storage/hosts /etc/hosts
        /opt/wz_mini/bin/busybox inotifyd /opt/wz_mini/usr/bin/watch_up.sh /tmp:n > /dev/null 2>&1 &
else
        mkdir /tmp/Upgrade
        /opt/wz_mini/bin/busybox inotifyd /opt/wz_mini/usr/bin/watch_up.sh /tmp:n > /dev/null 2>&1 &
fi

if [[ "$REMOTE_SPOTLIGHT" == "true" ]]; then
	/opt/wz_mini/bin/socat pty,link=/dev/ttyUSB0,raw tcp:"$REMOTE_SPOTLIGHT_HOST":9000 &
	echo "remote accessory enabled"
else
	echo "remote accessory disabled"
fi

if [[ "$ENABLE_MP4_WRITE" == "true" ]]; then
        if [ -f /opt/wz_mini/tmp/.T20 ]; then
		echo "mp4_write is not supported on T20"
	else
		/opt/wz_mini/bin/cmd mp4write on
		echo "mp4_write enabled"
	fi
else
	echo "mp4 write disabled"
fi

if [[ "$RTSP_HI_RES_ENABLED" == "true" ]]; then

        if [ -f /opt/wz_mini/tmp/.T20 ]; then
	HI_VIDEO_DEV="/dev/video6"
	else
	HI_VIDEO_DEV="/dev/video1"
	fi

	swap_enable

	if [[ "$RTSP_PASSWORD" = "" ]]; then
	RTSP_PASSWORD=$(cat /opt/wz_mini/tmp/wlan0_mac)
	fi

	/opt/wz_mini/bin/cmd video 0 on

        if [[ "$RTSP_HI_RES_ENABLE_AUDIO" == "true" ]]; then
		/opt/wz_mini/bin/cmd audio 0 on
		AUDIO_CH="-C 1"
		AUDIO_FMT="-a S16_LE"
		DEVICE1="$HI_VIDEO_DEV,hw:0,0"
        else
                DEVICE1="$HI_VIDEO_DEV"
		echo "rtsp audio disabled"
        fi

else
        echo "rtsp disabled"

fi


if [[ "$RTSP_LOW_RES_ENABLED" == "true" ]]; then

	if [ -f /opt/wz_mini/tmp/.T20 ]; then
	LOW_VIDEO_DEV="/dev/video7"
	else
	LOW_VIDEO_DEV="/dev/video2"
	fi

	swap_enable

	/opt/wz_mini/bin/cmd video 1 on

	if [[ "$RTSP_PASSWORD" = "" ]]; then
	RTSP_PASSWORD=$(cat /opt/wz_mini/tmp/wlan0_mac)
	fi

        if [[ "$RTSP_LOW_RES_ENABLE_AUDIO" == "true" ]]; then
		/opt/wz_mini/bin/cmd audio 1 on
		AUDIO_CH="-C 1"
		AUDIO_FMT="-a S16_LE"
		DEVICE2="$LOW_VIDEO_DEV,hw:2,0"
        else
                DEVICE2="$LOW_VIDEO_DEV"
                echo "rtsp audio disabled"
        fi

else
        echo "rtsp disabled"

fi

if [[ "$RTSP_LOW_RES_ENABLED" == "true" ]] || [[ "$RTSP_HI_RES_ENABLED" == "true" ]]; then
	echo "delay RTSP for iCamera"
	#This delay is required. Sometimes, if you start the rtsp server too soon, live view will break on the app.
	sleep 5
	LD_LIBRARY_PATH=/opt/wz_mini/lib /opt/wz_mini/bin/v4l2rtspserver $AUDIO_CH $AUDIO_FMT -F0 -U "$RTSP_LOGIN":"$RTSP_PASSWORD" -P "$RTSP_PORT" $DEVICE1 $DEVICE2 &
	sleep 1
        echo "Set imp variables via helper"
        /opt/wz_mini/usr/bin/imp_helper.sh > /dev/null 2>&1 &
fi

if ([[ "$RTSP_LOW_RES_ENABLED" == "true" ]] || [[ "$RTSP_HI_RES_ENABLED" == "true" ]]) && [[ "$RTMP_STREAM_ENABLED" == "true" ]] && ([[ "$RTSP_LOW_RES_ENABLE_AUDIO" == "true" ]] || [[ "$RTSP_HI_RES_ENABLE_AUDIO" == "true" ]]); then
	if [[ "$RTMP_STREAM_DISABLE_AUDIO" == "true" ]]; then
		RTMP_AUDIO="no_audio"
	fi
	echo "delay RTMP server"
	#Follow the delay from the RTSP server
	sleep 5
	/opt/wz_mini/bin/rtmp-stream.sh "$RMTP_STREAM_SERVICE" "$RTMP_AUDIO" &
fi

if [[ "$NIGHT_DROP_DISABLE" == "true" ]]; then
	touch /opt/wz_mini/tmp/.nd
fi

if [[ "$WEB_SERVER_ENABLED" == "true" ]]; then
        httpd -p 80 -h /opt/wz_mini/www
fi

hostname_set
touch /opt/wz_mini/tmp/.wz_user_firstrun
pkill -f dumpload #Kill dumpload so it won't waste cpu or ram gathering cores and uploading them when something crashes
sysctl -w kernel.core_pattern='|/bin/false'
dmesg_log
trim_logs
sync;echo 3 > /proc/sys/vm/drop_caches


if [ -f "$CUSTOM_SCRIPT_PATH" ]; then
	echo "starting custom script"
	$CUSTOM_SCRIPT_PATH &
else
	echo "no custom script configured in wz_mini.conf"
fi

echo "searching for custom scripts in /opt/wz_mini/etc/rc.local.d"
if [ -d "${1:-/opt/wz_mini/etc/rc.local.d}" ] ; then
  for filename in $(find /opt/wz_mini/etc/rc.local.d/ -name "*.sh" | /opt/wz_mini/bin/busybox sort) ; do
    if [ -f "${filename}" ] && [ -x "${filename}" ]; then
      echo "running ${filename}"
      "${filename}" &
    fi
  done
fi
echo "finished executing custom scripts from /opt/wz_mini/etc/rc.local.d"

echo "wz_user.sh done" > /dev/kmsg